Home Company Products Contacts Site map


Klinger® Gaskets > Gasket materials / PTFE Products > KLINGERSIL range > KLINGERSIL C-4400 - Technical data

  Gasket materials / PTFE Products
Technical data
High pressure gasket for universal applications. Suitable for use with oils, water, steam, gases, salt solutions,
fuels, alcohols, moderate organic and inorganic acids, hydrocarbons, lubricants and refrigerants,
food industry. Outstanding performance in many applications.
Typical values
Compressibility ASTM F 36 J % 11
Recovery ASTM F 36 J min % 55
Stress relaxation DIN 52913 50 MPa, 16h/175°C MPa 28
50 MPa, 16h/300°C MPa 25
Stress relaxation BS 7531 40 MPa, 16h/300°C MPa 23
Klinger cold/hot compression thickness decrease at 23°C % 10
50 MPa thickness decrease at 300°C % 20
Tightness according DIN 3535/6 mg/s x m 0.02
Tightness class L DIN 28090-1 0.1
Specific leakrate λ VDI 2440 mbar x l/s x m 1.64E-08
Cold compression DIN 28091-2 % 8 -12
Cold recovery DIN 28091-2 % 3 - 5
Hot compression DIN 28091-2 % < 15
Hot recovery DIN 28091-2 % 1
Spring back R DIN 28091-2 mm 0.019
Thickness increase after fluid oil JRM 903: 5 h/150°C % 3
immersion ASTM F 146 fuel B: 5 h/23°C % 5
Density g/cm3 1.6
Average surface resistance ROA Ω 3.6x10E10
Average specific volume resistance ρD Ω cm 1.4x10E10
Average dielectric strength kV/mm 24
Average power factor 1kHz, ca.3 mm thickness tan δ 0.147
Average dielectric coefficient 1kHz, ca.3 mm thickness εr 9.7
Thermal conductivity W/mK 0.40-0.42
ASME-Code sealing factors
for gasket thickness 2,0 mm tightness class 0.1 mg/s x m MPa y 20
m 3.5
of the standard sheets

1000 x 1500 mm,2000 x 1500 mm.
0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm; other thicknesses and sizes on request.
thickness ± 10%, length ± 50 mm, width ± 50mm
KLINGERSIL® gasket materials are generally furnished with surfaces of low adhesion. On request, graphite
facings and other surface finishes on one or both sides are also available. A non coloured version for food
application with technically identical values is named KLINGERSIL® C-4400L.
Function and durability
The performance and service life of KLINGER gaskets depend in large measure on proper storage and
fitting, factors beyond the manufactor’s control. We can, however, vouch for the excellent quality of our
products. With this in mind, please also observe our installation instructions.
Tests and approvals
BAM approval in accordance with UVV 28, oxygen (VBG 62) tested up to 100 bar and 80°C.
Approved for gas supply in accordance with DIN 3535/6. DIN-DVGW-permit NG-5123AT0251,
HTB tested. SVGW-permit, ÖVGW-permit, TÜV-Poland, KTW recommended, food toleration
Austria, WRC approval, Germanischer Lloyd, BS 7531 Grade Y. TA-Luft (Clean air) approval, tested in
accordance with VDI 2440 at 200°C.
Certified according to DIN EN ISO 9001:2000